Loydu.com'a Hoşgeldiniz

Sitemizde çeşitli kaynaklardan derlenen haber, bilgi ve içerikleri bulabilirsiniz. Şikayet ve telif bildirimleriniz için lütfen tıklayın.

How to Disassemble or Break Down a Large Projection TV

How to Disassemble or Break Down a Large Projection TV

Toshiba 50 inch Projection TV Model 50H82 Introduction Do you have large screen projection TV that you want to get rid off? This instruction will give you a guide on how to break down and disassemble ...

Toshiba 50 inch Projection TV Model 50H82Toshiba 50 inch Projection TV Model 50H82

Introduction

Do you have large screen projection TV that you want to get rid off? This instruction will give you a guide on how to break down and disassemble a projection TV into manageable pieces for disposal at a dump or landfill where the pieces and components can broken down further and have a chance for recycling.

This article with photographs uses a Toshiba 50H82, a 50 inch projection TV as a model. This TV had picture quality issues and repairs would cost almost the price of modern flat screen TVs. Large projection TVs are bulky and heavy. Getting rid of them can be expensive because the new High Definition TVs (HDTV) are cheap and nobody wants the massive projection TVs anymore. These beasts take up too much space. (See Fig 1)

Fig 1. A Large Screen Projection TV Hogging Up Living Room Space.Fig 1. A Large Screen Projection TV Hogging Up Living Room Space. | Source

Dismantling TV Overview

In my opinion, breaking down the Toshiba was not difficult. The design was user friendly for internal access. However, the case around the main components was glued. But I have a solution for destruction.

The TVs of today that uses LCD or LED technology are very lightweight. Even though I purchased a 50 inch LED TV with someone to help me, I really didn't need the assistance. The box is large but there were two straps to handle and carry the box. I am not that strong but I was able to lift the box and move it around by myself without any problems.

Older TV use cathode ray tubes (CRT) to provide video and there have been large CRT TVs made to provide screen sizes up to 36 inches. However, newer technology came around to support even larger screen sizes to provide a big screen movie experience. One of the technologies that became popular during the late 90's to early 2000's, were the Projection TVs. There were two types of projection TVs in the market: front and rear. A rear projection TV looks more like a standard television set.

The rear projection TV contains a red, green, and blue (RGB) projector, which produces the images to the back of the TV. This projector can be CRT, LCD, or DLP. The Toshiba 50H82 model uses CRT projectors. The back of the TV contains a mirror, which receives the picture which combines the RGB colors into any color from the original movie source (from cable, satellite, disc, and so on). The image that is projected to the rear mirror is what the viewer sees in the front screen.

Preparation

First, move the projection TV to a place where you can get dirty and make a mess. I used the living room at first to just remove all the heavy parts prior to moving it to a final disassembly area. In this case, I used my garage.

Gather all the tools needed to open up the case and remove components like large circuit boards. In the Toshiba 50H82, there were lots of small slotted lag screws. I used a cordless drill with an attachment to remove them.

Be mindful of any loose parts like screws or debris flying from using brute force during your work.


Remove Back Panel

I started the work behind the TV. There is a panel to access the large main circuit board. Unscrew the bolts or screws and remove the panel. (See Fig 2)

Fig 2. Removing the Back PanelFig 2. Removing the Back Panel | Source

Disconnect Power Cord

There is a power cord connection that was not accessible with the back panel in the way. With the back panel removed, you can see that the power cordis connected to the main board. Disconnect to get the cord out of the way. (See Fig 3)

Fig 3. Disconnecting Power CordFig 3. Disconnecting Power Cord | Source

Loosen Main Printed Circuit Board (PCB)

Locate any screws that fasten the main board to the base of the TV. Unscrew all of them until you find that the main board is loose. Once the board is loose, you can start disconnecting all the wires. (See Fig 4)

Fig 4. Loosening Main PCB Fig 4. Loosening Main PCB | Source

Disconnect Any Cables and Wires from PCB

Note in the pictures (Fig 5a and 5b) that there are several cables and wires connected to the main board. You can just cut them with wire cutters or scissor or disconnect by hand. I started disconnection by hand in case someone wanted to put the TV together again. After running into some connectors that seem impossible to remove, I just outright cut them.

I imaging some scavenger trying to put this TV together so I thought I would make it easy to put back together. Unfortunately, the connectors were so stuck and I was running out of patience.

 Fig 5a. Wires and Cables on Left Half of PCB Fig 5a. Wires and Cables on Left Half of PCB | SourceFig 5b. Wires and Cables on Right Half of PCBFig 5b. Wires and Cables on Right Half of PCB | Source

Put PCB Aside

After separating the cables from board, you can put it aside to work on the next step. (See Fig 6) As you can see it is quite large for a PCB.

Fig 6. Main Power Board Removed Fig 6. Main Power Board Removed | Source

Remove Front Panel

For the next step, I opened up the front bottom panel. I had the pry this cover from the side with a screwdriver. Once I got one area loose, I was able to work my way in separating the panel from the TV. (See Fig 7)

Fig 7. Removing Front PanelFig 7. Removing Front Panel | Source

Removing Middle Panel

There was another panel in the middle to access the RGB projectors. Unscrew and remove this cover and expose the projection system and associated circuit boards. (See Fig 8a and 8b)

 Fig 8a. Removing Middle Panel Under Front Panel Fig 8a. Removing Middle Panel Under Front Panel | SourceFig 8b. RBG Projection Assembly ExposedFig 8b. RBG Projection Assembly Exposed | Source

Remove Front Screen Part 1

We will need to remove the RGB projectors from the top. However, the large front screen is in the way and has to be removed. Ensure the large plastic piece holding the screen is unscrewed from the bottom.

This large screen slides up for removal. There are four 'hooks" that hold the screen in place. (See Fig 9)

Fig 9. One of 4 Hooks Holding Up Front ScreenFig 9. One of 4 Hooks Holding Up Front Screen | Source

Remove Front Screen Part 2

Grab the plastic piece from the bottom and lift up. The large screen is bulky but not heavy. Put the screen aside and out of the way. You will see a huge area for the projection of image going onto a large mirror on the inner back of the TV. (See Fig 10)

Fig 10. Screen Removed Showing Large Mirror BehindFig 10. Screen Removed Showing Large Mirror Behind | Source

Unscrew RGB Projector

Locate the screws that are holding the Red Green Blue (RGB) projector assembly from the top. (See Fig 11) Unscrew the projection system and ensure no wires are connected to the rest of the TV. If there are any connected wires, detach or cut.

Fig 11. Location of Screws Holding Projection AssemblyFig 11. Location of Screws Holding Projection Assembly | Source

Remove RGB Projector Assembly

The RGB projector assembly was the heaviest piece other than the large TV body. (See Fig 12) Put this piece in a box because there are many sharp edges that could hurt you. Put the box and the projector assembly out of the way.

Fig 12. RBG AssemblyFig 12. RBG Assembly | Source

Remove Speakers

The left and right speakers are held with 4 screws each side. Remove the speakers to lighten the TV. (Fig 12.5)

Fig 12.5. Remove SpeakersFig 12.5. Remove Speakers | Source

Smashing the Housing

Even with the main circuit board, front screen, RGB projection assembly and speakers removed, the hollowed out TV is still heavy and very bulky to put in a small truck. However, the TV is lighter for moving. You can now put the large TV in a big truck or van and get rid of it.

You now have the option of disassembling the TV body even further to transport the pieces in a small SUV or car.

The problem with the rest of the Toshiba 50H82 TV is that there are no other areas to unscrew. The remaining pieces are glued together. Brute force will be needed to break the rest but there is a large glass mirror to deal with.

The mirror slides out upward but the top of the TV is glued and in the way. I took a large heavy duty hammer to separate the left and right sides from the TV. The hammer I used is not the type used for removing nails on the other side of the tool. That hammer is too weak. I used the hammer akin to a small sledgehammer like the one Thor uses. (See Fig 13)

Fig 13. Heavy Duty Hammer Fig 13. Heavy Duty Hammer | Source

Remove Mirrow

After removing the top, I was able to slide the large mirror out and put it aside. (See Fig 14)

Warning: This is glass. Be cautious when handling!

Fig 14. Large MirrorFig 14. Large Mirror | Source

Breaking Housing Down Even More

I started removing the left side and right side with the hammer. After removing a few more odd particleboard pieces, all that was left is a piece that looks like a cabinet or table on wheels. (See Figures 15 and 16)

Fig 15. Removing Particle Wood BoardFig 15. Removing Particle Wood Board | SourceFig 16. Core of the TVFig 16. Core of the TV | Source

Recycling Ideas

After making the large wooden pieces small enough to fit in your van or truck, you can neatly stack the pieces in the vehicle and transport to your local landfill.

If you desire, the particleboard scrap wood can be reused for making furniture. The husk of the TV's cabinet can be converted to a table or cabinet for the new TV.

Epilogue

The Toshiba 50H82 50 inch rear projection TV has sentimental value. I purchased this TV around 2002 after my second kid was born and I knew I would be at home more to care for them. Having large high definition TV made entertaining kids and guests more fun.

Ten years later, the video started to get fuzzy. I was not able to play any console games like Nintendo Wii and Xbox 360 anymore. It would cost approximately $100 dollars just to have a technician just to come to the house to troubleshoot.

Leaving this goliath TV on the curb is just an eyesore. With HDTVs relatively cheap, why would anyone want an old projection TV that does not work correctly?

Goodbye, Big Screen Projection TV. You served a purpose well but newer technology has taken over. I mean some new TVs do not even carry the old RCA component or S-Video connectors anymore. HDMI connectors have taken over. Makes me wonder what the next ten years will bring with regards to television tech.







© 2012 Romian1

Comments

Sign in or sign up and post using a HubPages Network account.

0 of 8192 characters usedPost Comment

No HTML is allowed in comments, but URLs will be hyperlinked. Comments are not for promoting your articles or other sites.

sendingprofile image

Bob 

4 months ago

Thanks! I had the exact same make and model that had to come out of a basement after 18 years. Your guidance was very helpful!

Romian1 profile imageAUTHOR

Romian1 

6 months ago

Cooled by a liquid? They must have some really good seal to prevent leaking and evaporation.

profile image

John 

6 months ago

My Hitachi 57 inch was still working fine but was getting fuzzy after 16 years. I suspected it had dust inside somewhere. Turns out after tearing it apart It had dust on the lenses that I could have cleaned off had I known how to properly disasemble it. I salvaged a few parts I'm sure I don't need like the projector lenses. I thought it was interesting that the lamps were cooled by a liquid and there was a rubber bladder on the side of the heat sink housing to allow for expansion and contraction of the liquid. It was a realy good tv and served me well except for damaging my shoulder while moving it about 12 years ago.

Romian1 profile imageAUTHOR

Romian1 

7 months ago

Glad I could help. I knew others will be in the same situation.

Romian1 profile imageAUTHOR

Romian1 

7 months ago

Glad I could help. I knew others will be in the same situation.

profile image

Betty 

8 months ago

Thank you soooo much! I've been trying to push this 65" piece of Sony "furniture" around in this room, knowing full well that there was no way to get it out in one piece. (It took three delivery men, back around the late '90s, to get it in the house. And, they dropped the first one off the porch, had to go back and get another one, and one of them injured his back getting it in. I'm alone with this monster now, and I'm a 70 year old woman. However, I do some carpentry, haul and shovel rock, pull up fences, and clear cut wielding a 40 pound saw. I'm 5'3" tall and weigh 110 lbs, and my "opponent" weighs in at around 300lbs., is an inch or two taller than me, and is 65" wide. Now, thanks to you, I might very well get it out of here before they bring the new one!

Thanks again

profile image

Glen Williams 

8 months ago

I Have to thank you for the instructions it went well Thanks Glen

profile image

[email protected] 

2 years ago

how do I take down a 52" tv on the wall mounted frame?


Teknoloji Haberleri Kategorisinden Haberler